manualshive.com logo in svg

GE LOGIQ 400, Service Manual

Share
Download
GE LOGIQ 400 Service Manual Download Page 26

LOGIQ   400 SERVICE MANUAL

GE MEDICAL SYSTEMS

2127661

INTRODUCTION

1–14

REV 8

1–2–1 Warnings (Continued)

WARNING!

HAZARDOUS VOLTAGE. 140VDC CAN CAUSE A SEVERE INJURY OR DEATH, OR THE
POWER SUPPLY TO BE DAMAGED. TURN OFF THE POWER AND CHECK THE RESIDUAL
VOLTAGE OF CAPACITORS BEFORE ACCESSING THE POWER SUPPLY UNIT. CAREFULLY
WORK WHILE ACCESSING THE POWER SUPPLY UNIT.

OUTSIDE MARKINGS OF LOGIQ

 400 (ON POWER SUPPLY BOX)

ILLUSTRATION 1–11

Note

Same labels are attached on both left and right outside of the power supply unit.

Summary of Contents for LOGIQ 400















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands