GE LOGIQ 400 Service Manual Download Page 62 | Manualshive

Page: 62 / 526

GE LOGIQ 400 Service Manual Download Page 62

GE MEDICAL SYSTEMS

2127661

LOGIQ 400 SERVICE MANUAL



SYSTEM CONFIGURATION

3–14

REV 9

3–5–2 List of Optional Peripherals (continued)

3.

PROBES (Continued)

TABLE 3–5

LIST OF TRANSDUCERS (continued)

PROBE

MATERIAL OF

AREA OF

CATALOG

REQUIRED

NAME

HEADSHELL

USING

NO.

ADAPTER

LD

PES

BIOPSY

LINEAR

PA 51

C358

PES

ABDOMINAL

CONVEX

H45202CD

ERB7

NORYL

ENDOCAVITY

H40392LC

3S

NORYL

CARDIOLOGY

SECTOR

H4550SZ

No Needed

TYPE

FAMILY PROBES

PART No.

P9601AD

2193617
2172443

LINEAR/

CONVEX

2239590
2204232
2252157

Note

PES : Polyethersulfone NORYL : Modified Polyphenylene Oxide PU : Polyurethane

Note

Some probes listed on the table above have two different part numbers. The number of upper row
indicates the part number of probes for the region other than Japan. The number of lower row indi-
cates the part number of probes for Japan.
Probes which have only one part number are not available in Japan.

Note

546L, S317, S611, C386, I739, T739 and LA39 probes are available on LOGIQ



400 console from

software version 3.00.

Note

B510, S222, CWD2 and CWD5 probes are available on LOGIQ



400 console from software version

3.10.

Note

The following probes are not available on LOGIQ



400CL:

S220, B510, CWD2, CWD5, S317, S611, and S222

Note

The LD probe is available only for the Japanese console with the software version 3.40 or later.

Note

The C358 and ERB7 probes are available on LOGIQ



400 console with the software version 4.01 or

later.

Note

The 3S probe is available on LOGIQ



400 console with the software version 5.01 or later.

«
...
60
61
62
63
64
...
»

Summary of Contents for LOGIQ 400















































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands