manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

The GE Healthcare CARESCAPE Monitor B450 Technical Manual is available for free download on our website. This comprehensive manual provides detailed instructions and support for users of the B450 monitor. Visit manualshive.com to access this essential resource and optimize your experience with this cutting-edge product.

Share
Download
background image

CARESCAPE Monitor B450

 ii

2062973-003

3.7

User interface symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

4

Using Webmin service interface

39

4.1

Local access to Webmin using the integrated browser on the patient monitor . . . . . . . . . . 39

4.2

Local access to Webmin with a service PC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4.3

 Remote access to Webmin using a service PC over the IX Network  . . . . . . . . . . . . . . . . . . . . 41

4.4

Login to Webmin. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

4.5

Webmin configuration modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

4.6

Webmin information modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

4.7

Webmin diagnostics modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

5

Pre-installation requirements

49

5.1

Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5.2

Compatibility check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

5.3

Network infrastructure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.1 MC Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.2 Wireless MC Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.3 S/5 Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.4 S/5 Wireless Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
5.3.5 IX Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.4

Installing the mounting hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.5

Unity Network ID connectivity device installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

5.6

Power and environmental requirements  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

6

Hardware installation

55

6.1

Installing a battery into the patient monitor and the PDM module . . . . . . . . . . . . . . . . . . . . . . 55
6.1.1 Testing the battery charge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
6.1.2 Installing the battery into the patient monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
6.1.3 Installing the battery into the PDM module  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

6.2

Mounting the patient monitor  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

6.3

Connecting a secondary display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
6.3.1 Connections to D15K and D19KT displays  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

6.4

Installing parameter modules  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
6.4.1 Installing a PSM or a PDM module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

6.5

Connecting to the mains power  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

6.6

Connecting to the MC Network or the S/5 Network  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.7

Connecting to the IX Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.8

Connecting to a Unity Network ID connectivity device  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

6.9

Connecting USB devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

6.10 Connecting iCollect and other data acquisition systems  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
6.11 Connecting a remote-on cable  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
6.12 Connecting a local printer to the IX connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

7

Configuration

67

7.1

Adjusting display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.1.1 Adjusting the brightness of the integrated primary display . . . . . . . . . . . . . . . . . . . . . . 67
7.1.2 Calibrating a touchscreen  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.1.3 Adjusting optional secondary display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

7.2

Configuring the network  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
7.2.1 Configuring hostname. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B450

Laica SB2200 Instructions And Guarantee preview
SB2200
Brand: Laica Pages: 4
iGuzzini B183 Instruction Sheet preview
B183
Brand: iGuzzini Pages: 20
Landoll 2510 Series Operator'S Manual preview
2510 Series
Brand: Landoll Pages: 34
Panasonic LP-M Series Maintenance Manual preview
LP-M Series
Brand: Panasonic Pages: 174
Garelick 71095 Mounting And Operating Instructions preview
71095
Brand: Garelick Pages: 4
HANYOUNG NUX RLA-KB Series Quick Start Manual preview
RLA-KB Series
Brand: HANYOUNG NUX Pages: 2
ICP DAS USA I-2533T-FD User Manual preview
I-2533T-FD
Brand: ICP DAS USA Pages: 45
M-Audio FireWire 1814 Quick Start Manual preview
FireWire 1814
Brand: M-Audio Pages: 3
NanoVibronix UROSHIELD Quick Manual preview
UROSHIELD
Brand: NanoVibronix Pages: 2
NanoVibronix PainShield User Manual preview
PainShield
Brand: NanoVibronix Pages: 32
Nanoleaf Shapes Hexagons User Manual preview
Shapes Hexagons
Brand: Nanoleaf Pages: 27
Nautilus 9NP-B7524 Series Owner'S Instructions preview
9NP-B7524 Series
Brand: Nautilus Pages: 2
Nautilus Be strong NS 700X Owner'S Manual preview
Be strong NS 700X
Brand: Nautilus Pages: 34
Nautilus BE STRONG E916 Quick Start Manual preview
BE STRONG E916
Brand: Nautilus Pages: 21
PAS Systems International PAS V Instruction Manual preview
PAS V
Brand: PAS Systems International Pages: 24
PAS Systems International MARK V Alcovisor Operating Manual preview
MARK V Alcovisor
Brand: PAS Systems International Pages: 20
PARRY CPC Product Instructions preview
CPC
Brand: PARRY Pages: 14
York Fitness K850 Instruction Manual preview
K850
Brand: York Fitness Pages: 36

Brands by name

Popular brands

Load more brands