manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 163

 Troubleshooting

  155

2062973-003

Identical

 

IP address

 

noticed

A patient monitor with the 
identical IP address is on the 
network.

Disconnect the patient monitor that 
has the identical IP address.
or
Change the IP address of the patient 
monitor that has the duplicate IP 
address.

Service Monitor 
Error Code 
0xHOST1001

One of the internal 
temperature sensors indicate 
the inside temperature of the 
patient monitor is out of 
specification. The message 
stays on screen as long as the 
error condition is valid.

If temperature is too high:
1. Turn off the patient monitor.
2. Let the patient monitor cool down.
3. Check that the ventilation holes are 

not obstructed. 

4. Ensure that the patient monitor is 

installed to a location that meets 
the specified environmental 
requirements of operating 
temperature.

5.  Investigate the patient monitor 

thoroughly for potential short 
circuits and other electrical faults.

6. If possible, log in to Webmin and 

select 

Diagnostics> Hardware 

Stats

 to identify the root cause for 

the error message.

If temperature is too low (or high):
If the patient monitor has been 
transported or stored outside the 
operating temperature range, allow it 
to stabilize back to operating 
temperature range before applying 
power.

Service Monitor 
Error Code 
0xHOST1002

One of the internal supply 
voltages is out of the 
specification. The message 
stays on screen as long as the 
condition is valid.

Log in Webmin and select 

Diagnostics 

> Hardware Stats

 to identify the supply 

voltage that is below or above the 
specification limit.

Service Monitor 
Error Code 
0xHOST1004

Disk usage exceeds 90%.

1. Back up the clinical and platform 

settings and print the licensing 
information page via Webmin.

2. Re-install software.

Service Monitor 
Error Code 
0xHOST1100

The CPU timekeeper battery is 
empty. Time and date may be 
reset to factory settings.

Readjust time and date first. Replace 
the CPU timekeeper battery.

Message

Possible causes

Possible solutions

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands