GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 50

Page: 50 / 236

CARESCAPE Monitor B450

2062973-003

Record the IX IP address of the patient monitor:

IX IP address: ______________________

IX Netmask: ______________________

Configure the service PC’s IP address and subnet mask to the same network segment
with the patient monitor’s IX Network.

NOTE: For more information on how to configure the IP address, refer to the PC’s
documentation.
5.

Launch a web browser on the service PC.

In the

Address

field, type

https:

[IX IP address]:10000

and press

Enter

NOTE:

[IX IP address]

is the IX Network IP address of the patient monitor.

The

Login to Webmin

dialog box displays.

Continue to

4.4. Login to Webmin

Closing Webmin:

Restore the original network settings in the service PC.

Disconnect the service PC from the live IX Network.

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Related manuals for CARESCAPE Monitor B450

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Related manuals for CARESCAPE Monitor B450

Brands by name

Popular brands