GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 219

Page: 219 / 236

Service parts

211

2062973-003

13 Service parts

NOTE: Perform the specified checkout procedure steps described in chapter

10. Maintenance

and checkout

after you have replaced any service part.

13.1 Ordering parts

To order parts, contact GE Healthcare. Contact information is available at

www.gehealthcare.com

. Make sure you have all necessary information at hand.

13.2 List of FRUs

FRU/Item part
number

FRU/Item description

FRU content

M1233483

FRU, Recorder Unit, B450

Includes the thermal printer and recorder
interface board assembly.

M1233485

FRU, AC/DC Power Supply Unit, B450

Includes the complete AC/DC Power Supply
Unit with AC inlet, fuses, heat sink and the cable
to DC/DC board.

M1168221

FRU, Main Fuses (10 pcs), B450 & B650

FUSE, 4A, T, 250V, 5x20mm, high breaking
capacity 1500A, IEC, UL/CSA, CCC, 2 pcs

M1233487

FRU, Module Rail Unit, B450

Includes a complete PDM/PSM module rail unit
assembly with the 4 mounting screws.

M1233489

FRU, Battery Door Unit, B450

Includes a complete battery door assembly.

M1233490

FRU, LCD Display Unit, B450

Includes the LCD display with LED backlights,
display cable & LED backlight cable and the
gasket around the display.

2093301-001

FRU, Front Unit w. Touchscreen Sensor,
B450

Includes the complete plastic front bezel
subassembly with the touchscreen sensor &
cable.

M1233492

FRU, User Interface Board & Buzzer,
B450

Includes user interface board, user interface
cable, buzzer and the screws to mount the UI
board.

M1233493

FRU, Speaker Unit, B450

Includes the main speaker with cable.

10 M1233494

FRU, Alarm Light Unit, B450

Includes the alarm light board, alarm light
cable and plastic alarm light lens.

11 2091849-001

FRU, DC/DC Board, SJA B450

Includes the DC/DC board with the mounting
screw. Only for B450 monitors with product
code SJA. Changing this FRU may require
software upgrade

12 2089460-001

FRU, DC/DC Board, SNE B450

Includes the DC/DC board with the mounting
screw. Only for B450 monitors with product
code SNE.

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Related manuals for CARESCAPE Monitor B450

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Related manuals for CARESCAPE Monitor B450

Brands by name

Popular brands