manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 19

 System overview

  11

2062973-003

Keyboard

A washable, antibacterial keyboard is specified for 
use with the monitor. It may be connected to the 
monitor or display via one of the USB connectors. 
The keyboard allows you to enter data without 
using the touchscreen display.

                                                                    

 

Mouse

A standard mouse may be connected to the 
monitor or display via one of the USB connectors. 
The mouse allows you to select any on-screen 
items without a Trim Knob control or a touchscreen 
display.

                          

Remote control

The remote control provides all patient monitor 
controls on a portable component with a Trim Knob 
control. The remote control is connected to the 
patient monitor via one of the USB connectors.

                   

Barcode reader

The barcode reader can be used to scan a 
Technician ID and Patient Information from 
barcodes when admitting patients.

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands