GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 197 | Manualshive

Page: 197 / 236

background image

Disassembly and reassembly

189

2062973-003

3. Detach the WLAN card from the CPU carrier

board, if installed.
a. Remove the two screws (T6) that hold the

WLAN radio card to the CPU carrier board.
Torque [0.3 Nm].

b. Detach the WLAN radio card carefully

from its connector in the CPU carrier
board.

NOTE: Be careful not to damage the fragile WLAN
antenna boards or antenna cables.

4. Detach the grounding screw (T10) holding the

CPU assembly and AC/DC unit together.
Torque [1.6 Nm].

NOTE: During the reassembly, make sure to
fasten the grounding screw properly. This is
important to ensure that the CPU assembly is
properly connected to the protective earth.

5. Release the latch holding the CPU assembly

and pull the assembly out from the rear unit.

6. Carefully detach the uDOM from the CPU

assembly. The uDOM is connected to the CPU
assembly with a connector from one and with
a nylon support post from the other end. You
may need pliers to squeeze the nylon support
post a little to detach the uDOM.

NOTE: If replacing the CPU assembly, detach
the original uDOM from the CPU carrier board
and then attach it to the new CPU assembly.
The software, licenses and clinical and service
configurations are stored in the original
uDOM.

«
...
195
196
197
198
199
...
»

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B450

Brand: EASTERN INSTRUMENTS Pages: 93

Brand: Pari Pages: 2

Brand: ECE Pages: 2

Brand: Ecco Pages: 5

Evolution Series

Brand: Bakare Pages: 38

Brand: Jaga Pages: 32

Brand: Quick Pages: 24

Brand: JDS Uniphase Pages: 144

IP Video Test Option HST-3000

Brand: JDS Uniphase Pages: 14

9NP-B7524 Series

Brand: Nautilus Pages: 2

Be strong NS 700X

Brand: Nautilus Pages: 34

Brand: Nautilus Pages: 21

Brand: quadient Pages: 14

Brand: Qu-Bit Electronix Pages: 31

Brand: Tascam Pages: 78

MINISTUDIO CREATOR US-42

Brand: Tascam Pages: 11

Brand: Yacht Devices Pages: 68

Brand: Waves Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands