GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 174 | Manualshive

Page: 174 / 236

background image

CARESCAPE Monitor B450

166

2062973-003

PDM module issues

11.8.8 CARESCAPE Network communication issues

Traffic types

Two main types of communication occurs in the CARESCAPE Network: Broadcast and Unicast.
•

Broadcast traffic is sent from one device to all devices on the network. Examples of
CARESCAPE broadcast traffic are device discovery, alarms, and time synchronization.

•

Unicast traffic is sent from one device to another specific device on the network. An
example of CARESCAPE unicast traffic is patient waveforms.

Flow

•

Upstream broadcast: The patient monitor sends broadcasts to other network devices.

•

Downstream broadcast: The patient monitor receives broadcasts from other network
devices.

Possible cause

Recommended action

DC/DC board failure

The VSYS supply voltage for the PDM module is generated in the DC/DC
board. Check from the Webmin

Hardware Statistics

that the supply

voltages are within specification:
- VSYS voltage (mV)
- VSYS_EPORT(mV)
- VSYS_PDM (mV)
If PDM is connected to PDM dock, DC/DC board should identify PDM and
enable the VSYS_PDM circuit breaker on CPU carrier board to connect
VSYS voltage to VSYS_PDM.
If PDM is connected to ePORT, DC/DC board should identify PDM and
enable the VSYS_EPORT circuit breaker on CPU carrier board to connect
VSYS voltage to VSYS_EPORT.
If VSYS voltage is out of spec, the problem is most likely in the DC/DC
board. Replace the DC/DC board.

CPU assembly failure

The Ethernet communication for the PDM module is managed by the CPU
carrier board.

Check PDM Log for possible PDM errors messages, see section

If the cause is none of the above, the problem is most likely in the CPU
carrier boar. Replace the CPU assembly.

«
...
172
173
174
175
176
...
»

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B450

Brand: Baker Pages: 82

Brand: Olsen Pages: 4

Dominator Series

Brand: Falcon Pages: 31

Brand: Fakir Pages: 22

Brand: Qu-Bit Electronix Pages: 15

ST70 Instrument

Brand: Raymarine Pages: 12

Brand: Raven Pages: 73

Brand: Tascam Pages: 3

Brand: RAB Lighting Pages: 4

Brand: campgo Pages: 33

Brand: TC Electronic Pages: 4

Brand: TC Electronic Pages: 6

Brand: TC-Helicon Pages: 12

Brand: TC Electronic Pages: 76

Brand: Ultraflex Pages: 48

Brand: Lafayette Pages: 10

Brand: WARPP Pages: 28

Brand: Safco Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands