manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 45

 System overview

  37

2062973-003

Respiration indicator. Indicates a breath is detected by the impedance 
respiration algorithm.

BIS and Entropy sensor impedance check indicator (gray). Displays for 
each sensor as the impedance check is in progress.

BIS and Entropy sensor impedance check error indicator (red). Indicates 
the specified sensor failed the impedance check.

BIS and Entropy sensor impedance check passed indicator. Indicates the 
specified sensor passed the impedance check.

Completed NIBP volume icon. Adjust the volume of the tone that sounds 
when an NIBP measurement result is available.

Manual NIBP icon. Start a manual NIBP measurement.

Nellcor OxiMax SatSeconds indicator. Indicates the amount of time the 
SpO

2

 saturation is outside the limits before alarms are generated.

SpO

2

 signal strength indicator. Indicates the signal strength, with three 

asterisks indicating the strongest signal.

NMT Stimulus beep volume icon. Adjust the volume of the tone that 
sounds when a stimulus pulse is generated.

Progress bar. Indicates the amount of time remaining until the next 
automatic measurement.

The following symbols appear in the software user interface

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands