GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 213

Page: 213 / 236

Disassembly and reassembly

205

2062973-003

12.2.16 Detaching DC/DC board and E-Module board assembly

Disassemble first:
a.

12.2.6. Detaching the front unit and mid-frame assembly from the rear unit assembly

1. Detach the following cables:

- the touchscreen cable and the user

interface cable from the DC/DC board

- the speaker cable from the E-module

board

2. Detach the following cables from the DC/DC

board:
- Alarm light board cable
- LCD backlight cable

3. Remove the screw (T10) that mounts the

DC/DC board to the mid-frame assembly.
Torque [0.6 Nm].

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Brands by name

Popular brands