manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

The GE Healthcare CARESCAPE Monitor B450 Technical Manual is available for free download on our website. This comprehensive manual provides detailed instructions and support for users of the B450 monitor. Visit manualshive.com to access this essential resource and optimize your experience with this cutting-edge product.

Share
Download
background image

Table of contents

                                                             iii

2062973-003

7.2.2 Selecting and configuring CARESCAPE Network. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
7.2.3 Selecting and configuring S/5 Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
7.2.4 Configuring WLAN  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

7.3

Setting time and date . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

7.4

Setting unit and bed name . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

7.5

Configuring printers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
7.5.1 Installing a printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
7.5.2 Deleting a printer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
7.5.3 Printing a test page  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.6

Configuring Citrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

7.7

Configuring MUSE/12SL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

7.8

Admit settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
7.8.1 Patient ID prefix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
7.8.2 Barcode settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7.8.3 Configuring Length Delimited Parser information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
7.8.4 Configure character delimited parser information  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
7.8.5 Barcode data specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

7.9

Setting power frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

7.10 Selecting language and locale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.11 Selecting national requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
7.12 Configuring modules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

7.12.1 Module asset settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

7.13 Setting the host asset number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
7.14 Changing passwords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
7.15 Restarting the patient monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
7.16 Setting up the remote service  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

7.16.1 Configuring the remote service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
7.16.2 Enabling remote service agent/ connection  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
7.16.3 Testing the connectivity  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

7.17 Transferring settings from one patient monitor to other patient monitors. . . . . . . . . . . . . . . 89

7.17.1 Saving settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
7.17.2 Loading settings  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
7.17.3 Activating settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
7.17.4 Canceling pending settings activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

7.18 License management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

7.18.1 Enabling and activating host software package. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
7.18.2 Enabling and activating host software feature licenses. . . . . . . . . . . . . . . . . . . . . . . . . . 93
7.18.3 Uploading license file. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

7.19 Software management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

7.19.1 Transferring software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
7.19.2 Activating the installed software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
7.19.3 Canceling pending host software activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7.19.4 Erasing an inactive software version. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

8

Installation checkout

101

8.1

Visual inspection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

8.2

Electrical safety tests. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
8.2.1 Test setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
8.2.2 Power outlet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Related manuals for CARESCAPE Monitor B450

ParaBody 855 User Manual preview
855
Brand: ParaBody Pages: 5
Sagola 6110 Instruction Manual / Spare Parts List preview
6110
Brand: Sagola Pages: 20
Earmor C51 Quick Start Manual preview
C51
Brand: Earmor Pages: 5
Tacx Cosmos Assembling Instructions preview
Cosmos
Brand: Tacx Pages: 2
C.E. Nierhoff & Co C520 Troubleshooting Manual preview
C520
Brand: C.E. Nierhoff & Co Pages: 7
Olsen Infinity Operation Manual preview
Infinity
Brand: Olsen Pages: 56
Waterous K Series Operation And Maintenance Instruction preview
K Series
Brand: Waterous Pages: 5
3TECH TS-12 Manual preview
TS-12
Brand: 3TECH Pages: 32
4EVAC Compact 500 Operation Manual preview
Compact 500
Brand: 4EVAC Pages: 15
Federal 90 Series Troubleshooting Manual preview
90 Series
Brand: Federal Pages: 43
Datalogic Heron HD3430 Quick Reference Manual preview
Heron HD3430
Brand: Datalogic Pages: 48
PageFlip Firefly Quick Start Manual preview
Firefly
Brand: PageFlip Pages: 32
Gary Machinery 3354 Instruction Manual preview
3354
Brand: Gary Machinery Pages: 14
Pace ThermoTweez Handpiece TT-65 Operation & Maintenance Instructions Manual preview
ThermoTweez Handpiece TT-65
Brand: Pace Pages: 14
Salter PT-1700 Owner'S Manual preview
PT-1700
Brand: Salter Pages: 18
Salter KOR M-9590 Owner'S Manual preview
KOR M-9590
Brand: Salter Pages: 42
Salter KOR M-9530 Owner'S Manual preview
KOR M-9530
Brand: Salter Pages: 47
Salter FENX M-9640/L Owner'S Manual preview
FENX M-9640/L
Brand: Salter Pages: 35

Brands by name

Popular brands

Load more brands