manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 107

 Configuration

  99

2062973-003

activation is completed and the parameter module has restarted. This may take up to 15 
minutes. Do not shut down the patient monitor or disconnect the parameter modules. 
The parameter module restarts automatically after the software activation is complete. 

4.

After the parameter module restarts, verify that the software activation is successful and 
the parameter module runs the activated software.

7.19.3 Canceling pending host software activation

You can cancel a pending host software activation at any time while the message 

Software 

activation after next discharge/after next case end

 is shown on the display.

1.

Log in to Webmin.

2.

Select 

Configuration

 >

 Software Management.

 

 

The 

Software Management

 window opens.

3.

Select

 Host Software

 from the 

Software List

 and select 

Next

. 

4.

In the 

Host Software

 window, below 

Status

, verify that the 

Software activation pending

 

is 

Yes

.

5.

Select 

Cancel

. 

The pending software activation is cancelled and the patient monitor continues running the 
current software version.

7.19.4 Erasing an inactive software version.

You can erase an inactive host software version from the patient monitor. Erasing can prevent 
the activation of a wrong software version by mistake.
1.

Log in to Webmin.

2.

Select 

Configuration

 > 

Software Management

. 

 

The 

Software Management 

window opens.

3.

Select the software that you want to erase and select 

Next

. 

 

The selected software activation window appears. 

4.

Select 

Erase

 to erase the inactive software. 

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands