manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 103

 Configuration

  95

2062973-003

7.19.2 Activating the installed software

After transferring the new software to the patient monitors, take the transferred, inactive 
software into use by activating it.
Before you start:
•

Connect the patient monitor to the AC mains during software activation. Software 
activation does not start if the patient monitor uses its battery.

•

Verify the compatibility of the connected bedside and network devices with the new 
software version. Refer to the latest version of the CARESCAPE Modular Monitors 
Supplemental Information Manual for a list of compatible network and bedside devices.

•

Contact GE Healthcare to get the latest version of the user and service documentation

•

Contact GE Healthcare for any inquiries regarding the software CD and/or activation 
code for the new host software version.

NOTE: Loss of monitoring - Software is activated only when the patient monitor is in a patient 
discharged / case reset state. Normal patient monitoring is unavailable until the software 
activation is completed. This may take up to 10 minutes.
NOTE:  The existing clinical and platform settings of the patient monitor are saved and are not 
affected by the activation of the new patient monitor software version. However, any new or 
changed clinical and platform settings in the activated patient monitor software version have 
their factory default values and may require manual configuration. For more information, refer 
to the latest version of the CARESCAPE Modular Monitors Supplemental Information Manual. 
Contact GE Healthcare for any inquiries regarding the software CD and/or activation code for 
the new host software version. 
1.

Log in to Webmin.

2.

Select 

Configuration 

> 

Software Management

. 

 

The 

Software Management 

window displays.

3.

In the 

Software List

, select the software that you want to activate::

4.

Select 

Next

.

 

The selected 

Software activation

 window appears.

5.

According to the software you are activating, proceed to:
•

 Activating host software immediately

•

 Activating host software after next case end / discharge

•

 Activating module software

 

Software

Purpose of use

Host Software

Patient monitor software for the host unit including: 

•

PUIC SW for the DC/DC board

•

EMBC SW for the CPU Carrier board

PDM Software

CARESCAPE Patient Data Module 

PiCCO Software

E-PiCCO module.

sGAS Software

CARESCAPE respiratory modules, E-sCAiOV family. 

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands