GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 104

Page: 104 / 236

CARESCAPE Monitor B450

2062973-003

Activating host software immediately

Before you start:

•

Make sure the patient monitor is in a case reset / patient discharged state.

In the

Host Software

window, verify that the software you are activating is listed as

Inactive

Current Software State

Software License

, if applicable, enter the

Activation Code

for the new software

version.

Software Activation

, select

Immediately

Erase Inactive Software After Activation

, select:

Select

Activate

to start the host software activation.

Confirm activation by selecting

Yes

in the Host Software window that opens.

The patient monitor shows a screen saver that informs about the ongoing software
activation:

- to keep the currently active software version as inactive software after

the new software version is activated successfully. This option lets you
restore the patient monitor to the previous software version later.

Yes

- to erase the currently active software version permanently after the

new software version is activated successfully.

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Brands by name

Popular brands

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Search results

Summary of Contents for CARESCAPE Monitor B450

Reviews:

Brands by name

Popular brands