manualshive.com logo in svg

GE HEALTHCARE CARESCAPE Monitor B450, Technical Manual

Share
Download
GE HEALTHCARE CARESCAPE Monitor B450 Technical Manual Download Page 85

 Configuration

  77

2062973-003

4.

Select 

Save

.

7.7 Configuring MUSE/12SL

NOTE: MUSE viewing is a licensed software feature. You can configure the MUSE/12SL settings 
independent of the license status, but actual viewing of MUSE reports requires that the 
MuseView license is enabled.

Settings to send 12SL data

1.

Log in to Webmin.

2.

Select 

Configuration

 > 

MUSE/12SL

.

3.

In the 

MUSE/12SL

 window, enter the applicable information in the following fields:

Field name

Description and valid choices

Server Version

Select the supported server version: 4.0, 4.5, 
5.0, 6.0, 6.5.

Server 1 to Server 4 Addresses

Blank, server IP address or server hostname, 
up to 255 character long.

Initial Program

Initial Citrix- published application that will be 
launched, for example #MUSE. This field is 
mandatory, if the server address has been 
entered. The maximum length is 128 
characters.

Citrix Session Timeout (in Minutes)

Valid values are between 0-99. Keeping the 
session alive allows users to quickly return to 
their last session, but locks a Citrix license. 
Selecting "0" disables the timeout feature.

Username

Any valid Windows username. You can leave 
this field empty to allow anonymous login. 
The maximum length is 128 characters.

Password

Any valid Windows password. You can leave 
this field empty to allow anonymous login. 
The maximum length is 128 characters.

Confirm Password

The password and confirmed password must 
be the same.

Encryption Level

Select one of the following encryption levels:
- "Basic"
- "RC5 (128 bit - Login Only)" 
- "RC5 (40 bit)"
- "RC5 (56 bit)"
- "RC5 (128 bit)"

Summary of Contents for CARESCAPE Monitor B450













































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands