Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 42

Page: 42 / 285

Chapter 2 Checking before OS Installation

Performing Remote Installation

Before performing remote installation of ServerStart, use the following procedures to enable network

startup (PXE). In addition, check the MAC address.

Take the following steps in the BIOS Setup Utility.

1. Start the BIOS Setup Utility.

"8.2.1 Starting and Exiting the BIOS Setup Utility" (pg.205)

2. Select the [Peripheral Configuration] submenu from the [Advanced] menu and

press the [Enter] key.

3. Set [LAN Remote Boot] to [PXE].

4. Select [Save Changes & Exit] from the [Exit] menu and exit BIOS Setup Utility.

5. Start the BIOS Setup Utility again.

6. Select the [Boot Option] submenu from the [Main] menu and press the [Enter] key.

The Boot Option submenu window appears.

7. Change the [Boot Sequence] settings as shown below.

8. Exit the BIOS Setup Utility and turn off the server.

Check the MAC address.

Start up the server from the network.

The MAC address is displayed as shown below.

The MAC address is required for remote installation. Write it down.

You can turn the power on/off from a client (via a LAN) by utilizing the Wakeup On LAN (WOL)

function. Refer to "5.5.5 Turning the Power On via a LAN" (

pg.158).

Make sure to install ServerView to control the power supply via a LAN.

Unless ServerView is installed, the server is not turned off automatically after shutting down the OS.

1 CD-ROM Drive

2 Diskette

3 Hard Drive

4 Legacy LAN Card

5 Boot Manage PXE, Slot 0820 (or 0821)

CLIENT MAC ADDR: XX XX XX XX XX XX

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands