manualshive.com logo in svg

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Share
Download
Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 258

258

Chapter 9  Operation and Maintenance

9.7 Reinstalling the OS

This section explains the procedure for reinstalling the OS.

9.7.1 Checking before OS Reinstallation

■

Removing the Optional Devices

Remove the following optional devices before reinstallation. Install or connect them after OS 

installation.

• External SCSI optional devices (e.g., DAT unit) connected via a SCSI card

• Internal hard disk units that do not contain the OS installation folder

■

Deletion of Data from the Disk

Reinstallation deletes all disk contents. Be careful. Save the necessary data and system configuration in 

a different location.

Some drivers and software are not installed together with the OS. Install them after OS installation.

■

Other Notes

Any remaining notes are the same as those for initial installation. Make sure to check the settings in 

advance.

9.7.2 Reinstallation Using ServerStart

When the previous installation was performed in guided mode or preconfiguration mode, the ServerStart 

floppy disk used in that installation can be used again. When the reinstallation is performed with the 

same configuration as that for the previous installation, you do not have to edit the configuration file on 

the ServerStart floppy disk. You do not have to configure setting on wizards. After ServerStart starts up, 

click [Start (OS) Installation] to perform installation.

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands