Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 117

Page: 117 / 285

117

PRIMERGY RX100 S4 User’s Guide

Manu

al O

allation

Install the ChipSet driver.

1. Insert the ServerStart Disc 1 CD-ROM into the drive of the server.

If the ServerStart window appears, exit ServerStart.

2. Execute the following command on the ServerStart CD-ROM.

[CD-ROM drive] :\DRIVERS\ChipSet\Intel\Intel3000\Setup.exe

The installation wizard starts up.

3. Click [Next]. Follow the instructions in the window to perform installation.

4. When the "InstallShieled(R) wizard has completed" message appears, eject the

ServerStart CD-ROM from the CD-ROM drive and click [Finish] to restart the

system.

Install the LAN driver.

Install the LAN driver using the driver disk created from the ServerStart CD-ROM. For more

details, refer to "4.3 Installing the LAN Driver" (

pg.125).

Install the LAN driver advanced setup tool.

For information about onboard LAN driver advanced setup tool, refer to "5.6.1 BACS

Installation" (

pg.160). For information about LAN card advanced setup tool, refer to "5.7.1

Intel® PROSet Installation" (

pg.165).

Install the display driver.

1. Insert the ServerStart Disc 1 CD-ROM into the drive of the server.

If the ServerStart window appears, exit ServerStart.

2. Execute the following command on the CD-ROM.

[CD-ROM drive] :\DRIVERS\VIDEO\MATROX\w2k3x64\setup.bat

The installation wizard starts up.

3. Click [Next]. Follow the instructions in the window to perform installation.

4. When the installation is completed, eject the ServerStart CD-ROM from the CD-

ROM drive and click [Finish] to restart the system.

Install high reliability tools.

To ensure stable server operation, refer to "Chapter 6 High Reliability Tools" (

pg.169) and

install high reliability tools. For array type, RAID Management Tool (ServerView RAID) is

installed at the same time. When installing RAID Management Tool manually, refer to

"6.1.1

Installing RAID Management Tool" (

pg.170).

The installation of Windows Server 2003 x64 has completed.

Before Starting Operation

After OS installation, refer to "Chapter 5 Operations after OS Installation" (

pg.133) and perform the

necessary procedures.

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Search results

Summary of Contents for PRIMERGY RX100 S4

Reviews:

Brands by name

Popular brands