manualshive.com logo in svg

Fujitsu Siemens Computers PRIMERGY RX100 S4, User Manual

Share
Download
Fujitsu Siemens Computers PRIMERGY RX100 S4 User Manual Download Page 41

41

PRIMERGY RX100 S4 User’s Guide    

2

Checkin

g before O

S

 Inst

allatio

n

Cautions for Installing a Memory Module

This server supports up to 8GB of memory. However, the maximum installable size varies depending on 

the OS. Furthermore, since the server uses part of the memory as PCI resources, the maximum available 

size is limited. 

 

The following shows the maximum installable size and the maximum available size.

*1: The PCI resource is decreased, unless Service Pack 1 is applied and the following settings are configured 

using the BIOS Setup Utility. 

 

Available memory size shifts depending on the types and numbers of cards installed.

 

1. Start the BIOS Setup Utility.

 

2. Select the [Advanced System Configuration] submenu from the [Advanced] menu.

 

3. Set [NX Memory Protection] to [Enabled].

LAN Cable

Make sure to connect the LAN cable when the server is not connected to the Internet.

Connecting to the Internet during setup can cause security problems. Do not connect to the Internet 

until the setup completes.

If the OS is installed or applications are automatically installed without connecting the LAN cable to the 

LAN card, an error may be recorded in the event viewer after setup completes.

2.1.2 Hardware Settings

Before starting installation, set necessary hardware, such as the BIOS Setup Utility.

BIOS Setup Utility

The BIOS Setup Utility must be set in the following cases. For details on how to set the BIOS Setup 

Utility, refer to "8.2 BIOS Setup Utility" (

pg.205).

Changing the Boot Drive

To change the boot drive, start up the BIOS Setup Utility, select [Boot Option], and set the boot drive. 

 

"8.2.4 Boot Options Submenu" (pg.210)

table: Maximum Installable Size and Maximum Available Size

OS

Installed memory 

size

Available memory size

Windows 2000 Server

3.5GB or smaller

Same as the installed memory size

4.0GB

Installed memory size - (0.1GB)

Windows Server 2003

 

Windows Server 2003 R2

3.5GB or smaller

Same as the installed memory size

4.0GB

Same as the installed memory size 

*1

Windows Server 2003 x64

 

Windows Server 2003 R2 x64

Installed memory size

Same as the installed memory size

Summary of Contents for PRIMERGY RX100 S4






























































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands