FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 212

Page: 212 / 285

Using Auto-SYNC for Digital Input Connections

188 TIMS MVP

™

Setup and Configuration Guide

Connection Settings

The

Connection

tab is used to select boards, and video source and cable input type. Video

Source may not be selectable on certain model frame grabbers.

Changing the Miscellaneous Settings

Use the Miscellaneous tab to edit the following video settings:

Figure 89

Miscellaneous

Settings

Setting

Description

Vertical Sync Type

Specifies the type of sync
information that is available during
the vertical sync and vertical front
porch periods.

External Clock

For I-Series and AccuStream170
frame grabbers only. Not Used

Field Polarity

Specifies the order of the signal
fields.

Zoom Down

Old method of scaling for I-Series
and AccuStream170 frame
grabbers. Not Used.

Pitch

Specifies an absolute width
reserved for one line of video in
frame grabber (i.e. video board)
memory.

Enable Sync Filter

Used with the accustream170
series frame grabbers only.
Not supported in the
(Acc, AccuStream HD+
and HD+C series frame grabbers)

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands