FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 263

Page: 263 / 285

Using Auto-SYNC for Digital Input Connections

TIMS MVP

™

Setup and Configuration Guide 239

Changing SDTV Settings

Use the SDTV Settings tab to edit the following video settings:

Figure 134: SDTV Settings

It is easiest to adjust these video settings when continuous capture is active. Updating the
values in single snap mode can be slow.

Setting

Description

Brightness

The brightness adjustment
determines the black level of the
video processing.

Contrast

The contrast adjustment
determines the luminance
(proportional to intensity)
produced for white.

Hue

Changes the phase offset of the
chroma demodulator thus
changing the tint of the image.

Saturation

Sets the amount of color in the
image.

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands