FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 211

Page: 211 / 285

Using Auto-SYNC for Digital Input Connections

TIMS MVP

™

Setup and Configuration Guide 187

Changing Connection Settings

The options in the

Connection

tab concern the physical connection of the AccuStream board, as

well as its channel and sync source.

Figure 88: Connection video
settings

Setting

Description

Foresight Board

Selects the frame grabber to be
used.

Video Channel

RGB/YPbPr Analog & Digital
inputs are grouped as CA1.
Monochrome channels are
separate as CA1, CA2, CA3.

Sync Source

CA4 (Composite, Video Sync
Format, SS, (Separate H&V), SS-
H, (Inverted Hsync) SS-V,
(Inverted V Sync),

–

SS (H&V Sync

Inserted)

Pass Mode

Single Pass. Captures the
images in a single pass.
Double Pass no longer
supported.

RGB Cable

Selects the cable types used to
connect to the frame grabber.
DVI to BNC
DVI to VGA 15 pin DSub.
DVI to DVI (Either analog or
digital)
DVI to VGA 5BNC (Standard DVI
to 5BNC Analog cable)

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands