FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 29

Page: 29 / 285

Get Connected

TIMS MVP

™

Setup and Configuration Guide

Rear

View

(Backplane)

Connecting your TIMS MVP

™

System comprises standard PC connections (including network

connections) and Modality (imaging device) connections.

Indicate PC Connections

Your TIMS MVP

™

System is equipped with the full range of standard PC connection options and

peripherals. The items included with TIMS MVP

™

•

External Medical Grade Power Supply

—

US, Europe, or UK (as supplied)

IMPORTANT

: Make sure the external power coupler is not difficult to disconnect from a power

outlet. This includes ensuring it is not blocked or in an area where it would be very difficult to
access and/or remove quickly.

•

Keyboard

•

Mouse

•

DVI-D Cable

•

BNC Barrel Connectors, Qty 6

•

S-Video Cable

•

Network cable, Cat6

•

BNC Video Cable, Qty 2

•

BNC Trigger Adapter

•

Mono BNC to DVI Video Adapter

Modality Connection

PC Connections

Power Supply

Audio Connections

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands