FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 170

Page: 170 / 285

IDEA Auto-SYNC with RGB/VGA/DVI Analog Video

146 TIMS MVP

™

Setup and Configuration Guide

Changing the Miscellaneous Settings

Use the Miscellaneous tab to edit the following video settings:

Figure 51: Miscellaneous Settings

Setting

Description

Vertical Sync
Type

Specifies the type of sync information that is

available during the vertical sync and vertical front porch
periods.

External Clock

No longer supported.

Field Polarity

Specifies the order of the signal fields.

Zoom Down

Old method of scaling. No longer supported.

Pitch

Specifies an absolute width reserved for one line of
video in frame grabber (i.e. video board) memory.)

Enable Sync
Filter

Used only in the accustream170 series frame grabbers.
Not supported in the AS170+, 205a, HD+ and HD+C
series frame grabbers.

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands