FORESIGHT TIMS 2000 EN Setup And Configuration Manual Download Page 73

Page: 73 / 285

Getting Started

TIMS MVP

™

Setup and Configuration Guide 49

Configuring DICOM Destinations

The DICOM Server is configured on the TIMS MVP

™

Configuration page. This page allows you to:

•

Add a DICOM server to the TIMS MVP

™

system

•

Edit a DICOM server

•

Delete a DICOM server

•

Duplicate the configuration from an existing DICOM server

•

Override the Worklist Application Entity (AE) title

•

Add local settings for the worklist

Configuring DICOM Server Settings

There are two options you configure on the DICOM Servers home page:

•

Override the Application Entity (AE) title

•

Configure the Worklist local settings

To configure the DICOM Server settings:

Click the

Help

menu and select

Configuration

From the

TIMS MVP Config

page, click the

DICOM SERVERS

tab.

Summary of Contents for TIMS 2000 EN






























































































































































































































































































Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands

FORESIGHT TIMS 2000 EN, Setup And Configuration Manual

Search results

Summary of Contents for TIMS 2000 EN

Reviews:

Related manuals for TIMS 2000 EN

Brands by name

Popular brands