manualshive.com logo in svg

Flavor Burst CTP 80CBB, Equipment, Maintenance And Operations Manual

Share
Download
Flavor Burst CTP 80CBB Equipment, Maintenance And Operations Manual Download Page 47

 

46

Blending Assembly Suspension Bracket 

 

 

 

1.  Remove the bracket from the Blending 

Assembly and disassemble it. 

 

2.  Clean the bracket parts using warm 

detergent water and brush if necessary, 
then rinse thoroughly with warm water 
(108°F / 42°C). 

 

3.  Place the items in sanitizer solution for at 

least 5 minutes. 

 

4.  Remove parts from the sanitizer solution 

and place them on a sanitary tray to dry. 

 

5.  Reassemble and reinstall the bracket as 

directed in EQUIPMENT SETUP.

 

 

 
9-Tube Assembly Syrup Lines 

 

 

 

1.  If it is necessary, follow instructions in 

‘Phase 1’ and ‘Phase 3’ of the Clean-In-
Place procedure to clean and sanitize the 
coupler body, syrup line manifold, and the 
duckbill check valve. 

 

2.  Clean the coupler base, the end of the 

manifold and the outside of the syrup tubes 
with a towel and warm detergent water. 

 

3.  Rinse the parts using a single service towel 

and warm water (108°F / 42°C), then dry 
with a towel. 

 

4.  Reassemble the 9-Tube Assembly if 

necessary according to instructions in 
‘Phase 4’ of the Clean-In-Place procedure. 

Touch Panel and Mounting Bracket 

 

 

 
NOTE:

  DO NOT GET WATER NEAR THE 

CABLE CONNECTIONS OR SPEAKER 
HOLES ON THE TOUCH PANEL. 
 

NOTE:

  DO NOT USE ANY HARSH 

CHEMICAL CLEANERS, BLEACH, AMMONIA, 
EXCESS WATER, BRUSHES OR ABRASIVE 
TOOLS TO CLEAN THE SURFACE OF THE 
TOUCH PANEL.  THESE MAY DAMAGE THE 
SURFACE OF THE SCREEN AND VOID THE 
PANEL’S WARRANTY.  

 

 
1.  Turn the Touch Panel off by pressing the 

power button on the back side of the Panel. 
 

2.  Use only clean soft cloths, such as micro-

fiber cloths, to clean the Touch Panel 
surfaces.  Dampen a soft cloth with warm 
water (108°F / 42°C).  Wring out any excess 
moisture from the cloth.  

 
3.  Gently wipe the surfaces of the Touch Panel 

and mounting bracket to remove dust, dirt, 
fingerprints, etc. 

 
4.  Gently wipe the cables with the dampened 

cloth, taking care not to get any moisture 
near cable connections and any openings 
on the Touch Panel.    

 

5.  Use the dry soft cloth to dry the surfaces of 

the Touch Panel and cables.   

Detergent 

CLEAN

Water

RINSE

DRY

SANITIZE

26145

Detergent 

CLEAN

Water

RINSE

DRY

26143

Summary of Contents for CTP 80CBB

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands