Flavor Burst CTP 80CBB Equipment, Maintenance And Operations Manual Download Page 16

Page: 16 / 80

Syrup Pump and Related Parts (See Figure 4)

ITEM

PART NO.

DESCRIPTION

QTY.

FUNCTION

N/A

SOFT SERVE SYRUP PUMP

Pumps syrup from flavor bags to flavor
lines.

1A SYR 926P

PERISTALTIC SYRUP PUMP –
PREMIUM BEVERAGE

1 ea.

Pumps syrup from flavor bags to flavor
lines.

1B TUB 806

1/8” SYRUP PUMP REPL TUBE

1 ea. Transports syrup through pump.

1C FAS 2067

SYRUP PUMP TUBE WASHER-1/4

1 ea. Secures pump tube.

1D FAS 2066

SYRUP PUMP CLAMP-HOSE-1/4"

1 ea. Prevents pump tube from slipping.

1E FAS 2051

ROLLED FLANGE EYELET

1 ea. Creates tension for tighter fit.

1F FIX 1036

1/4" TO 1/4" OD UNION ELBOW

1 ea. Connects syrup in tube to pump.

1G FIX 1035

1/4 TO 3/16 OD REDUCING UNION 1 ea. Connects syrup pump to flavor line out.

SYR 944

SYRUP TUBE ASSEMBLY –
SOFT SERVE

Transports flavor from bag to pump.

2A FIX 1054

1/4” ID HOSE BARB SHUTOFF

1 ea. Connects flavor line to flavor bag.

2B SYR 902

FLAVOR-IN TUBE

1 ea. Carries syrup from syrup bag to pump.

2C TUB 811

TUBE-SILICONE .188X.375 PE
FB80

1 ea. Connects barb fitment to tube port.

2D FIX 1048

FITTING-1/4X1/4 BARB FB80

1 ea. Connects syrup tube to silicone tube.

SYR 927

INTERNAL 9-TUBE ASSEMBLY

Brings syrup from pump to Blending
Head.

3A SYR 900

4' 9-TUBE ASSEMBLY TUBE

9 ea.

Brings syrup from pump to Blending
Head.

3B ROT 511

LINE COUPLER NUT

1 ea.

Connects flavor lines to the internal
9-Tube Assembly.

3C ROT 512

TUBE CONNECTOR BODY

1 ea.

Connects internal 9-Tube Assembly to
flavor lines.

3D ROT 510

LINE COUPLER

1 ea. Holds flavor lines in place.

3E FAS 2051

ROLLED FLANGE EYELET

9 ea. Secures flavor lines to line coupler.

3F MIS 3023

FLAVOR LINE DUST CAP

1 ea. Cover to protect end of flavor lines.

CAB 113

FLAVORING TRAY

Houses syrup bags.

ELE 932

PUMP & SANITIZER CABLE
HARNESS

Provides power to the syrup and sanitizer
pumps.

Summary of Contents for CTP 80CBB

















































































Search results

Summary of Contents for CTP 80CBB

Reviews:

Brands by name

Popular brands

Flavor Burst CTP 80CBB, Equipment, Maintenance And Operations Manual

Search results

Summary of Contents for CTP 80CBB

Reviews:

Brands by name

Popular brands