ES&S DS850 Operator'S Manual Download Page 164 | Manualshive

Page: 164 / 199

background image

Chapter 10: System Messages

158

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

1009542 - Camera
Interface - Invalid
camera UART

X

X

This message appears if the BAPis
Image Processor Board receives an
invalid transmission from one of the
camera UART (Universal Asynchronous
Receiver/Transmitter) Modules.

Write down the error message and notify an
appropriate election official. If possible,
shutdown and then turn off the Scanner. Wait 30
seconds and then turn the Scanner back on. If
the problem persists, the UART may need to be
replaced. Contact an ES&S Service Technician.
Since the BAPis Board is a “COTS” (Commercial
Off The Shelf) product, the ES&S Technician may
have to contact a BAP Technician to fix the
problem.

1009543 - Camera
Interface - Camera did
not acknowledge
command

X

X

This message appears if the BAPis
Image Processor Board issues a camera
command, but the camera does not
acknowledge receipt of the command.

Write down the error message and notify an
appropriate election official. If possible,
shutdown and then turn off the Scanner. Wait 30
seconds and then turn the Scanner back on. If
the problem persists, contact an ES&S Service
Technician. Since the BAPis Board is a “COTS”
(Commercial Off The Shelf) product, the ES&S
Technician may have to contact a BAP Technician
to diagnose the problem.

1009544 - Camera
Interface - Illegal
character from camera

X

X

This message appears if one of the
cameras issues an illegal character in its
response to a command from the BAPis
Image Processor Board.

Write down the error message and notify an
appropriate election official. If possible,
shutdown and then turn off the Scanner. Wait 30
seconds and then turn the Scanner back on. If
the problem persists, contact an ES&S Service
Technician. Since the BAPis Board is a “COTS”
(Commercial Off The Shelf) product, the ES&S
Technician may have to contact a BAP Technician
to diagnose the problem.

System Messages

NOTE: A System Halt is a condition which requires the DS850 to be shutdown. It is not a condition which prevents the scanning of ballots.

Message Text

Message

Displayed

Message

Printed

Message

Logged

Results in a

System Halt

Cause

Resolution

«
...
162
163
164
165
166
...
»

Summary of Contents for DS850








































































































































































































Reviews:

No comments

Related manuals for DS850

Brand: Falcon Pages: 12

Brand: Eaton Pages: 16

RMQ-Titan C22-PV Series

Brand: Eaton Pages: 6

Brand: Eaton Pages: 98

Brand: Eaton Pages: 15

Brand: U-Line Pages: 2

Brand: Magnum Industrial Pages: 9

Brand: TMG Pages: 36

Brand: Swienty Pages: 31

Brand: Hubbell Pages: 2

MAXI-MIXER 4400 TRAILER

Brand: SAC Pages: 56

Mini Filter Wheel with OAG

Brand: Starlight Xpress Pages: 7

Brand: Viessmann Pages: 8

Brand: DRIESCHER-WEGBERG Pages: 25

Brand: ALFRA Pages: 38

Brand: OEZ Pages: 8

Brand: Workhorse Products Pages: 16

Brand: PFlow Industries Pages: 108

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands