background image

 Chapter 3: DS850 User Interface

41

EVS5200_DOC_SOP_DS850

 Software Version 2.10

 Published: February 26, 2014

Gate Flipper

Reports

Use the reports option to print the following reports:

Mark Code 

- contains the mark code data from the scanner’s image processor for 

the last ballot scanned and saved on the scanner.

Digital Readings

 - contains the reading data from the scanner’s image processor for 

the last ballot scanned and saved on the scanner.

Barcode Report

 - contains data from the scanner’s image processor for the last card 

scanned and saved on the scanner. It converts the barcodes on the card to a series 
of digits. 

Follow the steps below to print the reports:

1.

Press 

Reports

 on the Tests 

screen to display the Reports 
screen. 

2.

On the Reports screen, highlight 
the desired report by pressing 
on the report title and then press 

Print

.

3.

Press 

Done

 when you are finished printing reports.

Note: 

This section refers to future functionality that is not currently available on the DS850.

Note: 

ES&S Technicians use these reports to analyze scanner performance. 

Note: 

If the last ballot scanned was out-stacked, then the Mark Code and Digital Readings 

reports will not work because a ballot image was not saved for the last ballot scanned. 

Note: 

 The Zero, Results, 

Batch/Bin, Precincts 
Processed, and System 
Readiness reports are not 
available from this Reports 
screen. They are printed 
from the Reports menu. See 

Chapter 8: Reports

 for more 

information on accessing 
and printing those reports.

Summary of Contents for DS850








































































































































































































Reviews: