ES&S DS850 Operator'S Manual Download

Page: 119 / 199

Chapter 6: Election Day Tasks

113

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Export Audit Log

Follow the steps below to perform the Export Audit Log function:

Press

Election

to display the

Election menu.

From the Election menu, press

Results

to display the Results

screen.

From the Results screen, press

Export Audit Log

. This displays

the

Searching for ES&S Media

Device

pop-up screen.

Insert the Election Definition
Media Device flash drive or a
blank ES&S Media Device flash
drive into one of the scanner’s
USB ports. The previous
pop-up screen is temporarily
replaced by a

Detecting

inserted device

pop-up screen.

Then, the Election Code screen
appears.

Enter the Election Code and
then press

Accept

Reference:

See

Using USB Media Devices

for instructions.

Summary of Contents for DS850








































































































































































































Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands

ES&S DS850, Operator'S Manual

Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands