ES&S DS850 Operator'S Manual Download

Page: 97 / 199

Chapter 6: Election Day Tasks

EVS5200_DOC_SOP_DS850

Software Version 2.10

Published: February 26, 2014

Scanning

This section covers the following:



Scanning ballots



Handling out-stacked ballots



Saving a batch of ballots



Deleting a batch of ballots



Using the Sorting on/off feature

Scanning the Ballots/Cards

On the touch screen, press

Scanning

to display the

Scanning menu.

Warning:

The ballot scanning process assumes that the scanner has been powered on, all

pre-Election Day tasks have been completed, the election definition has been loaded, the
user has the authority to scan ballots, and the scanner has been calibrated.

Note:

Before you attempt to scan ballots/cards make sure that the camera lid and rear panel

are closed. The scanner does not allow functions that engage the motors to be performed
when the camera lid or rear panel is open.

Summary of Contents for DS850








































































































































































































Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands

ES&S DS850, Operator'S Manual

Search results

Summary of Contents for DS850

Reviews:

Related manuals for DS850

Brands by name

Popular brands