Epson S1C6S3N2 Technical Manual Download Page 100

Page: 100 / 270

I-88

EPSON

S1C6S3N2 TECHNICAL HARDWARE

CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Interrupt and HALT)

4.13 Interrupt and HALT

The S1C6S3N2 Series provides the following interrupt set-

tings, each of which is maskable.

External interrupt :

Input interrupt (two)

Internal interrupt :

Timer interrupt (three)

Stopwatch interrupt (two)

To authorize interrupt, the interrupt flag must be set to "1"

(EI) and the necessary related interrupt mask registers must

be set to "1" (enable).

When an interrupt occurs the interrupt flag is automatically

reset to "0" (DI), and interrupts after that are inhibited.

When a HALT instruction is input the CPU operating clock

stops, and the CPU enters the HALT status.

The CPU is reactivated from the HALT status when an

interrupt request occurs.

If reactivation is not caused by an interrupt request, initial

reset by the watchdog timer causes reactivates the CPU

(when the watchdog timer is enabled).

Figure 4.13.1 shows the configuration of the interrupt

circuit.

Summary of Contents for S1C6S3N2















































































































































































































































































Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands

Epson S1C6S3N2, Technical Manual

Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands