Epson S1C6S3N2 Technical Manual Download Page 77

Page: 77 / 270

S1C6S3N2 TECHNICAL HARDWARE

EPSON

I-65

CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Clock Timer)

This bit resets the clock timer.

When "1" is written :

Clock timer reset

When "0" is written :

No operation

Read-out :

Always "0"

The clock timer is reset by writing "1" to TMRST. The clock

timer starts immediately after this. No operation results

when "0" is written to TMRST.

This bit is write-only, and so is always "0" at read-out.

(1) When the clock timer has been reset, the interrupt factor

flag (TI) may sometimes be set to "1". Consequently,

perform flag read-out (reset the flag) as necessary at

reset.

(2) The input clock of the watchdog timer is the 2 Hz signal

of the clock timer, so that the watch dog timer may be

counted up at timer reset.

(3) Reading of interrupt factor flags is available at EI, but be

careful in the following cases.

If the interrupt mask register value corresponding to the

interrupt factor flags to be read is set to "1", an interrupt

request will be generated by the interrupt factor flags set

timing, or an interrupt request will not be generated.

Be very careful when interrupt factor flags are in the

same address.

TMRST:

Clock timer reset

(07EH·D3)

Programming notes

Summary of Contents for S1C6S3N2















































































































































































































































































Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands

Epson S1C6S3N2, Technical Manual

Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands