Epson S1C6S3N2 Technical Manual Download Page 51

Page: 51 / 270

S1C6S3N2 TECHNICAL HARDWARE

EPSON

I-39

CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Input Ports)

When an interrupt is triggered at the rising edge of the

input terminal, a factor flag will be set at the timing of

➁

shown in Figure 4.4.4. In this case, when the mask

registers cleared, then set, you should set the mask

In addition, when the mask register = "1" and the content

of the differential register is rewritten in the input termi-

nal active status, an input interrupt factor flag may be

set. Thus, you should rewrite the content of the differen-

tial register in the mask register = "0" status.

(4) Reading of interrupt factor flags is available at EI, but be

careful in the following cases.

If the interrupt mask register value corresponding to the

interrupt factor flags to be read is set to "1", an interrupt

request will be generated by the interrupt factor flags set

timing, or an interrupt request will not be generated.

Be very careful when interrupt factor flags are in the

same address.

Summary of Contents for S1C6S3N2















































































































































































































































































Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands

Epson S1C6S3N2, Technical Manual

Search results

Summary of Contents for S1C6S3N2

Reviews:

Related manuals for S1C6S3N2

Brands by name

Popular brands