manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 40

REV.-A

Other LEDs

POWER LED (Green) Lights when power is ON.

READY LED (Green) Lights 

when the printer can receive data.

PAPER OUT LED (Red) 

Lights when the paper is at the end.

D   A V LED (Yellow) Lights the setting for the 

 tear-off, 

micro adjustment, and platen gap

adjustment functions.

1.8.6.2 

 Function

This function is invoked 

when the 

 switch is pressed (except during ‘printing). When” this

function is invoked, the printer beeps and the message 

 

 is displayed.. In the

 function, major functions can be set by operating the ON LINE 

 FORM FEED (A), 

LINE FEED

(V), and LOAD/EJECT 

(D) switches. By pressing the 

 switch the second time the printer exits

this mode and returns to the ON-LINE 

mode. 

Exiting without performing “SAVE MACRO” or “SAVE

DEFAULTS” means that MACRO settings or DEFAULT settings will not be stored in the backup memory.

● 

Refer to Figure 1-21 for the entire 

 operational sequence.

 “

The 

 mode has five menus. While the message 

 MODE” is displayed, every time 

the LINE FEED (V) switch is pressed, the main menu of this mode is displayed in the order:

LOAD MACRO

Function in which the settings stored in one of the four macro channels can be read out and set as

the current 

 settings.

CHANGE MACRO

Function in which the current settings can be changed and stored into one of the four macro channels.

The twelve settings and their options are shown in Table 1-18.

CHANGE DEFAULTS

Functions in which the default settings shown can be changed. the default settings and options are

shown in Table 1-19.

PRINT OUT SETTINGS

Function in which all settings

CLEAR ALL MACROS

Function which all settings in

. . . . . 

in macro channels and the defaults can be printed out.

macro channels are cleared.

1-32

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands