manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 169

REV.-A

4.2.2  Upper Case Removal

Step 1:

Step 2:

Step 3:

Step 4:

Step 5:

Step 6:

Step 7:

Prin

Pull out the paper feed knob.

Remove the two printer covers. (Refer to arrows 

 through 

Remove the cartridge cover.

Remove the platen paper guide by turning it toward you.

Remove the three screws 

 X 12) securing the upper and lower cases.

Lift the front edge of the upper case and move it backward.

Disconnect connector CN21 on the 

 board, and remove the upper case.

Printer Cover

Cartridge Cover

 Cover

 Feed Knob

Figure 4-7. Upper Case Removal (1)

 

CBB 

   12)

Figure 4-8. Upper Case Removal (2)

Figure 4-9 shows the arrangement of the main components of this printer

upper case.

ROPS Board

 BOARD

(Power Supply Board)

\

(Control Board)

,

as seen after removing the

 Push Tractor

Printer
Mechanism

Unit

Figure 4-9. Main Components Arrangement

4-7

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands