manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 175

REV.-A

4.2.4.5

Step 1:

Step 2:

Step 3:

Step 4:

Battery Removal

Remove the upper case. (Refer to Section 4.2.2.)

Disconnect connector 

 on the ROMA board.

Insert a slotted screwdriver into the groove of the lower case, then unlock the tab of the battery

case.

Remove the battery together with the battery case.

 Battery Case

Screwdriver

/

G

I

Figure 4-18. Battery Removal

ADJUSTMENT REQUIRED

When connector 

 for the battery is disconnected, perform the following adjustment:

Section 4.3.5 Platen Gap Initial Value Write Operation (Page 4-46)

ASSEMBLY POINT:

● 

When mounting the battery, push down the tab of the battery case with a slotted screwdriver so

that it can be smoothly inserted into the lower case.

4 - 1 3

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands