manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 229

REV.-A

5.3 UNIT REPAIR

Unit repair is divided into three parts: ( 1 ) The 

 board; (2) The 

 board; (3) The Printer

mechanism.

This section will describe (l), the 

 board unit repair. If (2) 

 board or (3) Printer

mechanism should need repair, use the diagnostic tool introduced in Section 5.1.1.

5.3.1 

 Board

The power supply circuit 

 board is divided into three blocks:(1) Input filter circuit, (2) Main

switching circuits, and (3) Secondary side  (Refer to Figure 5-7.).

INPUT FILTER

MAIN SWITCHING

CIRCUIT

SIDE

TRANSFOl?-

,

MERS

I

+ 35 

 5V

*   1 2 V

Figure 5-7. 

 Board Block Diagram

If trouble occurs, first determine the faulty block and then find the bad component, referring to Tables

5-7 and 5-8, and Figures 5-9 to 5-13. in addition, Tables 5-9 and 5-10 list the parts used in the

 board.

DANGER

1. Before checking anything using the measuring instruments, check (that there are no metal chips

inside and that there are no burned components.).

2. Since this power supply is an isolated switching regulator, do not use a grounded measuring

instrument such as a 

 or oscilloscope. If a grounded instrument is used, fuse F 1 may

burn out. Be sure that the measuring instrument is not connected to ground before  using it on

this power supply circuit. In most cases, the line plug shown in Figure 5-8 will avoid this problem.

3. If your measuring instrument has multiple channels, measure the resistance value of each block

in the same way as described above and as shown in Figure 5-7. (Do not connect multiple

channels, such as channel 1 to the main switching circuit and channel 2 to the secondary side.)

4. Measure the resistance value on the circuit board after turn the power off.

Figure 5-8. AC Connector for Measuring Instruments

5-17

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands