manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 39

REV.-A

FONT Switch

Pressing this switch selects a font, and holding the switch for more than 1.0 second cycles through

the fonts sequentially. The LCD displays the currently selected font.

PITCH Switch

Pressing this switch selects 

the 

character pitch, and holding 

the switch for more than 1.0 second cycles

through the character pitches sequentially. The LCD displays the currently selected character pitch.

CONDENSED Switch

Pressing this switch selects normal or condensed printing.

CONDENSED LED (Green) Lights when condensed mode is selected.

PAPER SELECT Switch

Selects the paper. Each time this switch is pressed, the paper handling method changes in the following

order: TRACTOR, FRICTION, 

 BIN 1, 

 

 Each LED and the LCD displays the currently selected

paper handling.

 TRACTOR 

LED (Green) 

Lights when tractor feed is selected.

FRICTION LED (Green) Lights 

when friction feed is selected.

 LED 

(Green) Lights when 

 mode is selected.

TEAR 

OFF 

Switch

Advance the paper to the tear-off position. This switch is only effective for the tractor feed (Refer to

Section 1.8.1.2.).

TEAR OFF LED (Orange) Lights when the tear-off function is enabled.

MICRO FEED Switch

Selects or cancels the micro adjustment function. When this function is enabled, the LED on this switch

and the 

V 

and 

A 

 are lit. In the micro feed mode, the LINE FEED switch is used to feed the paper

backward and the FORM FEED switch is used to feed the paper forward. Paper feed performed in this

micro feed mode does not affect the page position control. This function is also used to adjust the paper

loading position and to adjust the paper to meet the tear-off edge (Refer to Section 1.8.1.2.).

 MICRO FEED LED (Orange) Lights when micro feed is enabled.

PLATEN GAP ADJUST Switch

Selects or cancels the platen gap adjustment function. When this function is selected, three 

 (A,

V, 

and the LED on this switch) are lit and the LINE FEED and FORM FEED switches are used to increase

and decrease the platen gap respectively. The relative platen gap value message is displayed on the

LCD. 

 level means to be widened. “-” level means to be narrowed. The limits of adjustment are

+0. 14mm 

to –O. 1 4mm.

PLATEN GAP ADJUST LED (Orange) Lights when the platen gap adjustment function is enabled.

 Switch

Selects or cancels the 

 function. When the 

 function is selected, the LED on this

switch is lit and the functions of the ON LINE, FORM FEED, LINE FEED, and LOAD/EJECT switches are

changed for the 

 function.

 LED (Orange) Lights when

 mode is selected.

1-31

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands