manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 190

REV.-A

4.2.5.15 Paper Release Solenoid Assembly Removal

.   

 ..:

.., 

W A R N I N G

When mounting the sensor, the stud should be fixed in the frame hole. Otherwise paper

release mechanism will not function correctly.

Step 1:

Step  2:

Step 

Step 4:

Step 5:

Step 6:

Remove the printer mechanism. (Refer to Section 4,2,5,1,)

Remove the paper tension assembly. (Refer to Section 4.2.5.5.)

Remove the paper feed motor, being careful not to lose the spring at the rear of the motor.

(Refer to Section 4.2.5.7.)

Remove the paper feed reduction gear and the platen. (Refer to Section 4.2.5 .10.)

Remove the tractor transmission gear and the paper release lever by pushing the loading

trigger plate in the direction of the arrow.

Remove the two screws 

 and 

 securing the paper release solenoid

assembly (one is for sensor and the other is for solenoid), then remove the paper release

solenoid assembly (sensor and solenoid).

 Release Lever

“Tractor Transmission

Loading Trigger Plate

Figure 446. Paper 

Release Lever Removal

Release  Trigger Plate

\

 

 -

Paper 
Planetary Lever

\

 

\ .

 

Gear

 

 

Release Sun Gear

Paper  Release Lever

 

.

\

—.

/Tractor Transmission Gear

 

 Release 

 

 Feed Reduction Gear “\

Figure 4-47. Paper Release Solenoid Assembly

Paper Feed 

Removal

- . - ’

4 - 2 8

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands