manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 191

REV.-A

ADJUSTMENT REQUIRED

When the paper release solenoid assembly is removed, perform the following adjustment:

Section 4.3.2 Paper Feed Motor Backlash Adjustment (Page 4-4 1)

ASSEMBLY POINTS:

● 

The lead wires from the sensor should be drawn along the frame to the rear of the printer and hooked

by the tabs on the loading frame.

Figure 4-48. Path of Sensor Lead Wires

● 

Before  mounting the paper release lever, confirm that the paper release planetary lever and the

release trigger plate are in their correct positions as shown in Figure 4-49.

● 

The positional relationship between paper release lever and paper release support lever is shown 

in Figure 4-50.

 Release Planetary Lever

Figure 4-49. Positional Relationship Between Release

Planetary Lever and Release Trigger Plate

 Release 

o

.-

0

 Release 

 

Figure 4-50. Positional Relationship Between Paper Release

Lever and Paper Release Support Lever

4-29

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands