Epson LQ-2550 Technical Manual Download Page 176

Page: 176 / 301

REV.-A

4.2.4.6 Cooling Fan Removal

Step 1:

Remove the upper case. (Refer to Section 4.2.2.)

Step 2:

Remove the push tractor unit. (Refer to Section 4.2.3. 1.)

Step 3:

Remove the ROMA board. (Refer to Section 4.2.4.1.)

Step 4:

the

board. (Refer to Section 4.2.4.2.)

Step 5:

Remove the eight screws

X 6) securing the ground plates, then remove the four

ground plates.

Step 6:

Remove the screw

X 8) securing the ground terminal of the power cord.

Step 7:

Remove the three screws

X 12) securing the base plate to the lower case.

12)

(o)

12)

X 6)

Base Plate

Plate

Power Cord

Figure 4-19. Base Plate Removal

Step 8:

Remove the two ground screws

X 6) at the rear of the printer, then remove the

base plate.

Step 9:

Tear off the three pieces of tape fixing the cooling fan wires to the lower case.

Step 10: Remove the two screws

X 12) securing the fan adapter to the lower case.

Step 1 1: Lift the cooling fan together with the fan screen and fan adapter, and remove them.

(0)

Figure 4-20. Ground Screws Removal

Tape

Lead Wire

Cooling

Fan

Fan Screen
Fan Adapter

X 12)

Figure 4-21. Cooling Fan Removal

4-14

Summary of Contents for LQ-2550














































































































































































































































































































Search results

Summary of Contents for LQ-2550

Reviews:

Brands by name

Popular brands

Epson LQ-2550, Technical Manual

Search results

Summary of Contents for LQ-2550

Reviews:

Brands by name

Popular brands