manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 184

4.2.5.8

Step 1:

Step 2:

Step 3:

Step 4:

Platen Gap Motor Removal

Remove the printer mechanism. (Refer to Section 4.2.5. 1.)

Remove the two screws 

 X 8) securing the platen gap motor.

If the platen gap home position flag prevents the motor securing screw from being

removed, manually rotate the platen gap reduction gear so that the screw can be removed.

NOTE: Do  not hold the platen gap home position flag to rotate the gear.

Remove the wire clamp fixing the lead wires of the platen 

gap 

motor from the base frame.

Take out the platen gap motor through the cutout at the back of the base frame, then separate

the lead wires from the motor by disconnecting the connector. (The lead wire is supplied

independently of the platen gap motor. The motor lead wire is included in the platen gap home

position sensor assembly.)

Platen Gap Reduction Gear

I

Platen Gap
Home 

Position

Sensor

\

CPS 

Platen Gap  Home Position

Figure 4-35. Platen Gap Motor Screw Removal

Flag

Connector

●

●

 

 

cutout

 ,

!

m

 

 

 

 “ 

 

.

Figure 4-36. Platen Gap Motor Removal (Back of Base Frame)

4-22

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands