manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 206

4.3.4 Platen 

Gap Home Position Sensor Mounting Position Adjustment

This adjustment is required when:

. The platen gap home position sensor mounting position is shifted.

● 

The platen gap gear is replaced.

● 

The platen is replaced.

Step 1:

Step 2:

Step 3:

Step 4:

Step 5:

Step 6:

Step 7:

Step 8:

Step 9:

Remove the printer mechanism. (Refer to Section 4.2.5. 1.)

Remove the 

 (Refer to Section 4.2. 1.)

Remove the CB screw 

 X 5), then remove the paper width sensor from the ribbon mask.

(See Figure 4-74.)

Remove the two 

 screws 

 X 5), then remove the ribbon mask.

(See Figure 4-74.)

Attach the 

 by the two 

 screws 

 X 6).

Move the carriage to the center of the platen.

Rotate the platen gap motor pinion little by little manually so that the gap between the platen

and 

 can be adjusted to 1.2 [mm] using a thickness gauge. (See Figure 4-78.)

Loosen the 

 screw 

 X 8) securing the platen gap home position sensor (See Figure

4-80).

Connect extension cable E649 (modified cable; see Figure 4-79.) between the 

 board

(CN 16) and the 9 pin connector of the printer mechanism.

Step 10: Attach the probe of either the oscilloscope or multi-meter (digital type) to CN 16 of the 

board. (Connect the plus and minus probes to pins 8 and 9, respectively. When using the

oscilloscope, its ranges should be 2 V/DIV. and 1 

Step 1 1: Turn the printer power on.

Step 12: Move the platen gap home position sensor along the groove on left frame, and fix it at the

position where the voltage changes from O to 0.1 

 (low level) to 5 

 using the 

screw. (See Figure 4-80.)

NOTE: If the voltage does not reach 5.0 

 even after the platen gap home position sensor was moved

to the back of the mechanism, loosen the screw 

 

   8) and move the platen gap home

position flag to clockwise until the voltage reaches 5.0 

 (See Figure 4-80.) At this time, make

sure that the platen gap gear does not move.

    

 

4 - 4 4

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands