manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 12

Feeding Method

Friction feed

Tractor feed (push: standard, push-pull: optional)

NOTES: 1. When using friction feed:

● 

Select friction feed on the control panel.

● 

Do not use continuous (fanfold) paper.

● 

Do not use a single sheet paper shorter than 92mm or longer than 364mm

● 

Do not perform any reverse paper feed operations within the top 8.5 mm and bottom

22 mm of the paper.

● 

Do not perform reverse feed beyond 1/6” after the paper end has been detected.

● 

Do not use multi-part, single-sheet forms.

2. When using push-pull tractor feed:

● 

Select tractor feed on the control panel.

● 

Mount the pull tractor unit (optional).

● 

Do not loosen the paper between the platen and the pull sprocket.

● 

Precisely align the horizontal position of the pull sprocket and push tractor.

● 

Do not perform reverse feeding for more than 1/6”.

● 

Do not perform reverse feeding after the paper end has been detected.

● 

Multiple copy paper must be pasted together using line or dots.

● 

Copy paper must be carbonless multi-part paper.

Paper Loading Directions

Fanfold paper

Inserted from the rear

Cut sheet paper

Inserted from the top

Line Spacing

1/6”, 1/8”, or programmable in units of 1/1 80” 

Line Feed Speed

See Table 1-3.

Table 1-3. Line Feed Speeds

Feeding Method

1/6” 

line spacing

Continuous

[ins/line]

[inch/s]

Friction without 

Friction with 

84

4.0

Tractor

1-4

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands