manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 177

4.2.5  P r i n t e r   M e c h a n i s m   D i s a s s e m b l y

This section describes the procedures for disassembling

mechanism. Refer to Figures A-56 and A-57  in the appendix

REV.-A

the main components of the printer

during assembly.

4.2.5.1

Step 1:

Step 2:

Step 3:

Step 4:

Step 5:

Step 6:

Printer Mechanism Removal

Remove the upper case. (Refer to Section 4.2.2.)

Remove the push tractor unit. (Refer to Section 4.2.3. 1.)

Disconnect twelve connectors CN 15, 

 13, 

 12, 

 

 CN 10, CN9, CN 16, 

 CN 19,

 CN 17 and CN 18 from the 

 board, which connect the printer mechanism to the

 board.

Remove the eight screws 

   securing the ground plates, then remove the four

ground plates. (See Figure 4-1 9.)

Remove the five screws CB(M4 X 6) securing the printer mechanism to the lower case.

Remove the printer mechanism.

CN15

 13

 12

 

 

 

   

 \ \

 

 

CN 18

Figure 4-22. Connector Locations

 

 -

Printer
Mechanism

 Board

 (M4 X 6)

CB 

 6)

Figure 4-23. Printer Mechanism Removal

ADJUSTMENT REQUIRED

● 

When the printer mechanism, is removed or replaced, perform the following adjustment:

Section 4.3.5 Platen Gap Initial Value Write Operation (Page 4-46)

● 

When the printer mechanism is replaced, perform the following adjustment:

Section 4.3.6 

 Printing Alignment (Page 4-47).

4-15

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands