manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 193

REV.-A

● 

When setting the paper loading lever, observe the following sequence.

 Align the two marks on the loading gear A and the loading gear assembly.

 Set the paper loading lever so that the marks on the lever is in alignment with the mark on the

loading gear A.

 Lever

Loading Gear A

 Gear Assembly

Figure 4-53. Paper Loading Lever, Loading Gear A,

Loading Gear Assembly Setup

 Install the loading lever shaft, and tighten the screw temporary.

 Check the following operations of the loading planetary gear.

(2)

The platen gear should engage the loading planetary gear and the planetary gear should

follow the platen gear when it rotates.

When pressing the loading trigger plate in the direction of the arrow, the loading planetary

gear  should engage loading gear A so that the rotation of the platen gear is transmitted to

the loading gear. If the loading planetary gear does not work well, adjust it using the screw

CPS (P) 

 8) securing the loading frame.

r

1

Loading Lever

Trigger

Loading 

 

Figure 4-54. Loading Planetary Gear Operation

 Tighten the loading lever shaft and the screw securing the loading frame.

 Install the loading gear spring.

ADJUSTMENT REQUIRED

When the paper loading trigger assembly is removed, perform the following adjustment:

Section 4.3.2 Paper Feed Motor Backlash Adjustment (Page 4-4 1)

4-31

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands