manualshive.com logo in svg

Epson LQ-2550, Technical Manual

Share
Download
Epson LQ-2550 Technical Manual Download Page 173

REV.-A

ADJUSTMENT REQUIRED

● 

When the 

 board is replaced, perform the following adjustment:

Section 4.3.6 Bi-directional Printing Alignment (Page 4-47)

● 

When the connector 

 for the battery is disconnected, perform the following adjustment:

Section 4.3.5 Platen Gap Initial Value Write Operation (Page 4-46).

4.2.4.2

Step 1:

Step 2:

Step 3:

Step 4:

Step 5:

 Power Supply Board Removal

Remove  the upper case. (Refer to Section 4.2.2.)

Remove the push tractor unit. (Refer to Section 4.2.3.1.)

Disconnect connector 

 from the 

 board, which connects the 

board to the 

 board.

Disconnect connector 

 1 from the 

 board, which connects the power switch

to the 

 board.

Remove the two 

 12) screws and four 

 screws securing the 

 board to the lower case, and remove the 

 board.

 (o)

 12)

 8)

 

CP (o) -

 Board

(M3 

 12)

Figure 4-15. 

 Board Removal

4-11

Summary of Contents for LQ-2550














































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands