Electriq Power PowerPod 2 Installation Manual Download Page 32

Page: 32 / 146

Installation Manual

1. Use the wall-mounted bracket as a template and drill holes in the
wall, 10mm in diameter and 80mm deep.

Fix the wall-mounted bracket on the wall using the plastic anchors in
the accessories bag.

2. Carry the auto-transformer by holding the heatsink on two sides and
place the equipment on the mounting bracket.

3. Secure auto-transformer to wall bracket 5mm x 12mm, torque min.
2.1 max. 2.5 Nm (1.5 min. 1.8 max. ft lb).

4. Take a picture within the PowerTools app.

CAUTION:

The auto-transformer is small in size, but very

heavy. It is recommended that two people carry it during
installation.

L’auto-transformateur est de petite taille, mais très lourd. Il
est recommandé que deux personnes le portent pendant
l’installation.

Mounting System / Auto-Transformer

Plastic Anchors

Summary of Contents for PowerPod 2



















































































































































Search results

Summary of Contents for PowerPod 2

Reviews:

Related manuals for PowerPod 2

Brands by name

Popular brands

Electriq Power PowerPod 2, Installation Manual

Search results

Summary of Contents for PowerPod 2

Reviews:

Related manuals for PowerPod 2

Brands by name

Popular brands